Page 1 of 1

.577 Snider

Posted: Fri Jan 06, 2017 8:59 am
by Ovenpaa
Is anyone here shooting a .577 Snider and if so how are you getting on with it and would you recommend owning and shooting one or is there an alternative to consider?

Re: .577 Snider

Posted: Fri Jan 06, 2017 10:10 am
by 3bravo
I own and shoot a snider carbine, I'm just finishing cleaning up and restoring a mk111 short rifle I also have a 11* currently off f.a.c.
Shoots lovely, cartridges I either buy from kranks or restyle magtech 24g. brass, for plinking I use cheddite 24g plastic cut down .

Re: .577 Snider

Posted: Fri Jan 06, 2017 10:41 am
by dromia
I just love Sniders.

Here is a review I did of the best Snider bullet out there bar none.

It has gone on to develop even far better groups that the first ones shot here.

Red River Ricks .590" Collar Button

This thread follows on from the one in the Group buy Forum

here:http://castboolits.gunloads.com/showthread.php?t=25795

I can confirm that the mould is a beauty its right up there with the best bespoke moulds.

Here it is fitted to a pair of Ricks quality handles.

Image



Image



Image



The mould halves fit together seamlessly with just the right amount of slight resistance as they finally close.

The sprue plate was little tight for my taste but is easily adjusted, as can be seen from the photographs it is plenty thick to allow alloy pull into the mould on cooling.

The mould was cleaned with isopropyl alcohol and it was ready to cast.

So on to the pot and lets see how she casts :-D

Alloy for this Boolit is as close as I can get to pure lead, this is roof flashing and has a BH of just under 6.

Here's the pot, the mould and ladle heating up.

Image

I ran the alloy temperature up to 850 for starters and began casting, I was using a rowel ladle and it took around a dozen and a half casts to get all the wrinkles out and the mould up to temp.

Boolits were looking good but base fill out wasn't perfect, I upped the temp to 900 and that sorted that out, next time I'll slacken of the sprue plate a tad. I then got into rhythm with boolits dropping consistently.

The handles needed a tap to drop the boolits but that is due to the depth of the lube groove rather than and finish problems, a light tap and out they came.

I tried using the Lyman dipper as well but it didn't give as good results as the Rowel, mainly incomplete base edge fill and as I've said slackening the sprue plate will help here methinks.

About half way through the session I applied some Bull Plate Sprue lube to the mould. Now I rate this product very highly but when applied to Ricks mould I noticed no difference in operation other than the no smear if you open the sprue plate early. The stuff is doing its job its just that the fit is so good that you don't notice any improvement as there isn't room for any. This has only happened with my Borton Darr moulds, pretty impressive.

After about three quarters of an hour I felt the need for a cup of tea so brought the session to and end and I'd around 80 boolits ready for inspection.


Image


The boolits weighed in at half a grain either way of 351 grains.

I had 78 boolits in this weight range and 18 rejects, these were the ones that were used for getting the mould up to temperature and the incomplete base fill with the Lyman ladle.

I then checked the boolits for roundness using Gussy's Cabine Tree hardness tester.

Image


Image


Again very impressive, there was the odd flicker on the dial as I rotated the boolit but nothing over 1 thou and that could have been as much my ham fistedness rotating the boolit as the boolit's condition.

From a casting point of view we have a real winner here, have I mentioned that this is class act of a mould.

So now to lubing.

The boolits miked out at a very consistent .5915" with my alloy on both bands (?).

A good fit for the Snider methinks

The boolits were sized, well hardly, on my Vickers lube sizer. This beast was made for .577 Boolits so Buckshot was able to craft a .590" lube die for me.

For lube I use my own beeswax/lanolin/olive oil mix that is pretty soft and keeps any BP fouling down.

These boolits take a lot of lube each one needing a three quarters rotation of the piston to fill the groove.

Image

Image


Almost filled


Image


Another tweak and its finished


Image


Don't they look totally different when lubed


Image

All thats left to do now is load the rounds.

Loading .577 Snider

I'm using my standard .577" Snider load of 75 gns of Swiss No5 powder with slight compression of a sixteenth of an inch after filling the case through a 36" drop tube, in a converted CBC 24 bore shotgun case fired with a Federal pistol primer.

Over the powder is 3 gns of washed and carded wool.

Being a .590" boolit I was worried about getting the case expanded enough for seating but one of my older NDFS dies sets had an "M" die like step in it and this give me enough flare to start the boolit.

Here's the cases having the wool added.

Image

Three grains, no more no less.

Image


Now time to seat the boolit.

Image


Image


The finished Item, ready to go.

Image

So how do they shoot?

Haven't a clue but I'm at the range tomorrow and weather permitting we'll find out.

I've put up some reference rounds with the RCBS Minnie for comparison and I'll be using three Sniders for the test one with the three groove 1 in 72" twist a three band Mk1 * , a two band 5 groove 1 in 48" Mk111 and an Artillery Carbine with the same barrel as the two band.

So range report to follow. :-D

How does it shoot?

About as good as it casts. :-D

The following are 50 yrd 5 rnd groups off a rest.

These are with no load development just the standard .577 load.

2 1/2" MK111.

Image


4" MK1*


Image


4 1/2" Artillery Carbine

Image


In all cases these groups were fired from a clean barrel, in all three the lowest shot in the group was the first.

In the Mk1* group the second lowest shot was called by the shooter.

Bearing in mind the nature of the sights on these rifles and variable technique of the shooters these are good groups.

It was a pleasure to shoot with the lighter boolit giving noticably less recoil than the standard minnie.

For me this boolit is a winner and with work and care repeatable accuracy will come from these rifles, especially the two band, using Red River Rick's .590" Paradox Mould.

Rick won't be getting this one back. :-D

The rifles.

Many thanks to Rick for sticking his neck out on this and the result is a testament to the man's technical skill and understanding of the subject.

The rifles:


Image


Image

Re: .577 Snider

Posted: Fri Jan 06, 2017 11:50 am
by 3bravo
Great post Dromia far more experienced than me, just learned a hell of a lot.
Hope some of it sinks in thanks.

Re: .577 Snider

Posted: Fri Jan 06, 2017 2:20 pm
by davidh195
Adam

Is your Snider short rifle a 5 groove?

I ask as iv'e a Mk3 5 groove short rifle & have been undecided about trying that bullet for a while.

Edit. Ok iv'e found the answer :oops:

David

Re: .577 Snider

Posted: Fri Jan 06, 2017 2:22 pm
by dromia
davidh195 wrote:Adam

Is your Snider short rifle a 5 groove?

I ask as iv'e a Mk3 5 groove short rifle & have been undecided about trying that bullet for a while.

David
Yes.

Re: .577 Snider

Posted: Fri Jan 06, 2017 3:14 pm
by David Nimrod
dromia wrote:I just love Sniders.

Here is a review I did of the best Snider bullet out there bar none.
Brilliant post, fascinating, I have lots to learn! :good:

Re: .577 Snider

Posted: Sat Jan 07, 2017 6:10 am
by ChAoS
You gentlemen might enjoy watching this YouTube channel:

https://www.youtube.com/user/britishmuzzleloaders

Regards,

Mark.

Re: .577 Snider

Posted: Sat Jan 07, 2017 8:45 am
by AL8
I shoot a Nepalese 3 band Snider with CBC Magtec 24 ga brass with a .600 round ball.
If I do my bit I can hit the torso of a fig 11 every time at 100 yards.