.31 cal Revolver Loading press?

Anything muzzle loading in here. Old and new, rifles, shotguns, pistols and even cannons!

Moderator: dromia

Post Reply
Message
Author
CDM5
Posts: 547
Joined: Fri Oct 26, 2012 6:41 pm
Home club or Range: Tidworth RPC & Bisley
Location: Wilts
Contact:

.31 cal Revolver Loading press?

#1 Post by CDM5 »

I'm interested in a 31 calibre 1848 baby dragoon, however the lack of loading lever means a hand press would be required to load the cylinder off of the frame.

Is there an option for a ready made press or loading tool? The sellers I've spoken to (Kranks) have said they don't have a press small enough.

Thanks
User avatar
dromia
Site Admin
Posts: 19964
Joined: Sat Nov 06, 2010 4:57 am
Home club or Range: The Highlands of Scotland. Cycling Proficiency 1964. Felton & District rifle club. Teesdale Pistol and Rifle club.
Location: Sutherland and Co Durham
Contact:

Re: .31 cal Revolver Loading press?

#2 Post by dromia »

DIY is the best way to go.

Set a piece of dowel as near a diameter as possible to the cylinder pin diameter.

Put cylinder over board mounted dowel.

Pour powder.

Seat ball with a piece of dowel and a soft faced hammer.

Mark the seating dowel with tape to the required seating depth for consistency.
Image

Come on Bambi get some

Imperial Good Metric Bad
Analogue Good Digital Bad

Fecking stones

Real farmers don't need subsidies

Cow's farts matter!

For fine firearms and requisites visit

http://www.pukkabundhooks.com/
User avatar
Sim G
Past Supporter
Posts: 10726
Joined: Sat Nov 06, 2010 9:09 pm
Contact:

Re: .31 cal Revolver Loading press?

#3 Post by Sim G »

On the range, quick and dirty, I'd pour powder into the chambers so about a quarter of an inch below the mouth, and press the ball home with my thumb. You'd be surprised how easy it is. I've read the original method was to remove the cylinder and use the arbour to seat home the balls.

Or, take the cylinder off and use a 7mm solid brass rod with the end con-caved with a chamfer bit, them as Adam says, a couple of smart taps with a hammer.

Use 4Fg instead of the usual 3, around 10 to 11 grains by volume and a .319 ball. Smart crack, no recoil barely, but forget any distance beyond 15yds for anything meaningful on a target!
In 1978 I was told by my grand dad that the secret to rifle accuracy is, a quality bullet, fired down a quality barrel..... How has that changed?

Guns dont kill people. Dads with pretty Daughters do...!
User avatar
bradaz11
Sporadic Site Supporter
Posts: 4714
Joined: Mon Jun 02, 2014 1:23 am
Home club or Range: The tunnel at Charmouth, BWSS
Location: Bristol
Contact:

Re: .31 cal Revolver Loading press?

#4 Post by bradaz11 »

i just use the arbour on mine.
When guns are outlawed, only Outlaws will have guns
User avatar
Sim G
Past Supporter
Posts: 10726
Joined: Sat Nov 06, 2010 9:09 pm
Contact:

Re: .31 cal Revolver Loading press?

#5 Post by Sim G »

Traditionalist. Ironically, that's the way forward... lol
In 1978 I was told by my grand dad that the secret to rifle accuracy is, a quality bullet, fired down a quality barrel..... How has that changed?

Guns dont kill people. Dads with pretty Daughters do...!
User avatar
bradaz11
Sporadic Site Supporter
Posts: 4714
Joined: Mon Jun 02, 2014 1:23 am
Home club or Range: The tunnel at Charmouth, BWSS
Location: Bristol
Contact:

Re: .31 cal Revolver Loading press?

#6 Post by bradaz11 »

i do have a 'tower of power' that should do it. but I just use my cheap kranks loader for my 44s so the tower stays in a cupboard gathering dust.
When guns are outlawed, only Outlaws will have guns
Post Reply

Who is online

Users browsing this forum: No registered users and 8 guests